Perkins 2806F Engine Flexible Exhaust Pipe Removal Procedure

This article describes the Perkins 2806F engine disassembly procedure for flexible exhaust pipes

2023A& 2022A Perkins EST Electronic Service Tool Diagnostic Software Full Provide Installation Service


CAUTION:

The ends of the bellows are very sharp. Injury could occur if the bellows are not handled properly Handle the bellows by the convolutions


NOTICE:

The bellows must be supported at all times when the bellows are not installed in the application. Failure to support the bellows adequately could result in the failure of the bellows. Do not use power tools in order to disassemble or assemble any part of the flexible exhaust system.

The alignment of the bellows is important. Incorrect alignment may lead to premature failure of the bel- lows. Misalignment can be identified by visually in- specting the uniformity of the spacing between the convolutions on the bellows.

Inspect the bellows for damage prior to installation. If there is any damage to the convolutions, discard the bellows. If there is any difficulty in installation after the repair, discard the bellows.







Typical example:

1. The lateral alignment of the bellows is critical. All the components must be assembled in the same alignment as prior todisassembly. The components that require correct lateral alignment are shown at Position (A) and Position (B).

Perkins SPI2 Version 2018A Service & Parts Catalogue Software




a. Use suitable material to encase flexible exhaust pipe (3). Encasing the flexible exhaust pipe will prevent damage of the bellows. Encase bellows for the flexible exhaust pipe between Position

(C) and Position (D). Use cablestraps to retain the suitable material.

Note: Ensure that the flexible exhaust pipe is

supported at all times.

b. Loosen ball clamp (1) from the flexible exhaust pipe assembly.

c. Loosen ball clamp (5).

d. Remove the assembly of the flexible exhaust pipe from CEM (2) and elbow connection (4).

Note: Ensure that the assembly of the flexible

exhaust pipe is supported as the ball clamps are removed.

Disassembly Procedure for the Flexible Exhaust Pipe Assembly

1. Ensure that all components of the flexible exhaust pipe assembly are clean and free from wear and damage. If necessary, replace any components of the flexible exhaust pipe assembly that are worn or damaged. Refer to your Perkins distributor for further information.


Typical example

2. Follow Steps 2.a through Step 2.d to remove the flexible exhaust as an assembly from Clean

Emission Module (CEM) (2) and elbow connection (4) on the turbocharger.

a. Use suitable material to encase flexible exhaust pipe (3). Encasing the flexible exhaust pipe will prevent damage of the bellows. Encase bellows for the flexible exhaust pipe between Position

(C) and Position (D). Use cablestraps to retain the suitable material.

Note: Ensure that the flexible exhaust pipe is

supported at all times.

b. Loosen ball clamp (1) from the flexible exhaust pipe assembly.

c. Loosen ball clamp (5).

d. Remove the assembly of the flexible exhaust pipe from CEM (2) and elbow connection (4).

Note: Ensure that the assembly of the flexible

exhaust pipe is supported as the ball clamps are removed.

Disassembly Procedure for the Flexible Exhaust Pipe Assembly

1. Ensure that all components of the flexible exhaust pipe assembly are clean and free from wear and damage. If necessary, replace any components of the flexible exhaust pipe assembly that are worn or damaged. Refer to your Perkins distributor for further information.






2. If necessary, follow Step 2.a through Step 2.d to disassemble the flexible exhaust pipe assembly.

a. Make temporary marks in Position (F) on all components of the bellows (3) and tube

assembly (7) to show correct orientation and alignment.

Note: Do not scribe the components to mark the position of the flexible exhaust pipe

assembly.

b. Loosen clamp (6) and remove tube assembly (8) from bellows (3).

c. Remove bellows (3) from tube assembly (7).

d. Remove tube assembly (7) from adapter (9).

Note: Ensure that the flexible exhaust pipe bellows are not subjected to any undue stress.
Perkins Engine ECM ECU Flash Files Collection Download

Perkins 2806F Engine Relay (ARD Nozzle Heater) Removal Instructions

This article introduces the Perkins 2806F engine relay (ARD nozzle heater) removal instructions

2023A& 2022A Perkins EST Electronic Service Tool Diagnostic Software Full Provide Installation Service
1. Turn the battery disconnect switch to the OFF position.












2. Cut cablestraps (3) from harness assembly (4)

Note: Note position of cable straps. Ensure that all

cablestraps are removed for the harness

assemblies.

3. Slide the locking tab for the harness assembly (4) into the unlocked position.

4. Disconnect harness assembly (4) from harness assembly connection (5) for the clean emission module.

5. Remove bolts ( 1) and spacers.

Note: Note position and orientation of any brackets that are attached to the relay assembly.

6. Remove relay assembly (2) from the bracket for the clean emission module.

7. If necessary, follow Step 7.a through Step 7.b to remove relay assembly (2) from bracket (6).

a. Remove bolts (7) from relay assembly (2) and remove bracket (6).

Note: Note the orientation of the bracket for

installation purposes.

b. Remove relay (2) from bracket (6).

Installation Procedure

1. Ensure that all components are clean and free

from wear and damage. If necessary, replace any components that are worn or damaged.




Perkins SPI2 Version 2018A Service & Parts Catalogue Software




Typical example

2. If necessary, follow Step 2.a through Step 2.b to install relay assembly (2) to bracket (6).

a. Position relay assembly (2) onto bracket (6).

Note: Ensure the correct orientation of the relay assembly on the bracket.

b. Install bolts (7) to relay assembly (2) and tighten the bolts to a torque of 9 N·m (80 lb in).

3. Position brackets onto relay assembly (2) and install bolts (1) and spacers.

Note: Ensure correct position and orientation of the brackets.

4. Position relay assembly (2) onto the bracket for the clean emission module.

Note: Ensure that the relay assembly is correctly oriented on the clean emission module bracket.

5. Tighten the bolts to a torque of 12 N·m ( 142 lb in).

6. Connect harness assembly (4) to harness

assembly connection (5) for the clean emission module.

7. Install cablestraps (3) to harness assembly (4).

Note: Ensure that cablestraps meet the Original Equipment Manufacturer (OEM) specification.

8. Turn the battery disconnect switch to the ON

position.
Perkins Engine ECM ECU Flash Files Collection Download

Perkins 2806F Engine Combustion Head Installation Procedure Guide

This article introduces the Perkins 2806F engine combustion head Installation procedure

Installation Procedure

2023A& 2022A Perkins EST Electronic Service Tool Diagnostic Software Full Provide Installation Service

 
1. Ensure that all components are free from wear or damage.

2. Clean the combustion head. Refer to Systems Operation Testing and Adjusting, Swirl Plate (ARD Combustion)-Inspect/Clean for the correct procedure.

3. If necessary, follow Step 3.a through Step 3.d to assemble combustion head (21).

a. Install combustion head (21) into a suitable support.

b. Install a new O-ring seal (25) (not shown) and new O-ring seal (27) (not shown) to adapter (24)
and adapter (26).

c. Install adapter (24) and adapter (26) to combustion head (21). Tighten the adapters to a torque of 30 N-m (266 lb in).

d. Install adapter (22) and adapter (23) to combustion head (21). Tighten the adapters to a torque of 60 N-m (44 Ibft).

Perkins SPI2 Version 2018A Service & Parts Catalogue Software

 
4. If necessary, install studs (18). Tighten the studs to a torque of 17 N-m (150 Ib in).

5. Install a new gasket (20). Install tube assembly
(19) and a new gasket (17).

6. Apply Tooling (A) onto the threads of studs (18).

 

7. Install combustion head (21). Install nuts (16).
Tighten nuts (16) in a crisscross pattern to a torque of 23 N-m (204 Ib in).
Tighten the nuts again in a crisscross pattern to a torque of 23 N-m (204 Ib in).
Tighten the nuts again in a crisscross pattern to a torque of 23 N-m (204 Ib in).

8. Install ARD spark plug (15) to combustion head
(21). Refer toDisassembly and Assembly, ARD Spark Plug -Remove and Install for the correct procedure.

Perkins EST Diagnostic Adapter-High Quality

 
9. Install flame detection temperature sensor (11) and flame detect (12). Refer to Disassembly and Assembly, Temperature Sensor (DPF Inlet, Flame Detect)-Remove and Install for the correct procedure.

10. Remove caps from adapters and plugs from hose assembly (6), hose assembly (7), hose assembly
(9), and hose assembly (10).

11. Install hose assembly (6), hose assembly (7), hose assembly (10), and tube assembly (9).
Ensure that the hose assemblies and tube assembly are installed into the correct positions.

12. Tighten the tube nuts for the hose assembly (6)
and hose assembly (7) to a torque of 13 N-m
(115 lb in). Ensure that the hose assemblies are not strained as the tube nuts are tightened.

13. Tighten the tube nuts for tube assembly (9) and hose assembly (10) to a torque of 25 N-m
(221 lb in). Ensure that the hose assemblies and the tube assembly are not strained as the tube nuts are tightened.

14. Connect high tension lead (8) to the spark plug.

15. Position ground strap (14) onto the combustion head. Install bolt (13) to the ground strap. Tighten the bolt to a torque of 12 N-m (106 Ib in).

Perkins Engine ECM ECU Flash Files Collection Download
16. Install tube assembly (3) to hose assembly (2).

17. Install a new gasket (5) (not shown) between tube assembly (3) and the combustion head. Ensure that the gasket is correctly orientated.

18. Apply Tooling (A) onto the threads of bolts (4). Install the bolts to tube assembly (3). Tighten the bolts to a torque of 28 N-m (248 Ib in).

19. Tighten hose clamp (1) to a torque of 11 N-m
(97 lb in).

20. Turn the fuel supply to the ON position.

21. Turn the battery disconnect switch to the ON position.

22. Perform the ARD ignition test. Refer to Troubleshooting Manual, "ARD Ignition -Test"for the correct procedure.

Perkins 2806F Engine Combustion Head Removal Procedure Guide

This article introduces the Perkins 2806F engine combustion head removal procedure


a. Remove the Exhaust Elbow.

WARNING

Fuel leaked or spilled onto hot surfaces or electri-

cal components can cause a fire. To help prevent

possible injury, turn the start switch off when

changing fuel filters or water separator elements.

Clean up fuel spills immediately.

Perkins Engine ECM ECU Flash Files Collection Download

NOTICE:

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



WARNING


Hot engine components can cause injury from burns. Before performing maintenance on the en- gine, allow the engine and the components to cool.

1. Turn the fuel supply to the OFF position.

2. Turn the battery disconnect switch to the OFF

Start By:

2023A& 2022A Perkins EST Electronic Service Tool Diagnostic Software Full Provide

2023A& 2022A Perkins EST Electronic Service Tool Diagnostic Software Full Provide Installation Service
3. Loosen hose clamp (1) on hose assembly (2).
4. Remove bolts (4) and remove tube assembly (3).
Remove gasket (5) (not shown).

5. Disconnect hose assembly (6), hose assembly (7), hose assembly (10), and tube assembly (9). Cap the adapters and plug the hose assemblies.
6. Remove bolt (13) from ground strap (14).
7. Disconnect high tension lead (8) from the sparkplug. Position the high tension lead away from the combustion head.

8. Remove flame detection temperature sensor (11)
Assembly, Temperature Sensor (DPF Inlet, Flame Detect) -Remove and Install for the correct and flame detect (12). Refer toDisassembly and procedure.

9. Remove Aftertreatment Regeneration DeviceRefer to Disassembly and Assembly, ARD Spark Plug-Remove and Install for the correct procedure.
(ARD) spark plug (15) from combustion head (21).
10. Remove nuts (16) from combustion head (21).
Remove the combustion head.
11. Remove gasket (20), tube assembly (19), and gasket (17).
12. If necessary, remove studs (18).

 

Perkins EST Diagnostic Adapter-High Quality

13. If necessary, follow Step 13.a through Step 13.d to disassemble combustion head (21).
a. Install combustion head (21) into a suitable support.
b. Remove adapter (22) and adapter (23) from combustion head (21).
c. Remove adapter (24) and adapter (26) from combustion head (21).
d. Remove O-ring seal (25) (not shown) and O-
ring seal (27) (not shown).

Perkins 2806F Engine Solenoid Valve (DEF Heater Coolant)-Remove and Install Guide

This article introduces Perkins 2806F Engine Solenoid Valve (DEF Heater Coolant)-Remove and Install

2023A& 2022A Perkins EST Electronic Service Tool Diagnostic Software Full Provide Installation Service

Removal Procedure：
NOTICE Care must be taken to ensure that fluids are con-
tained during performance of inspection, mainte-
nance, testing, adjusting and repair of the product.
Be prepared to collect the fluid with suitable contain-
ers before opening any compartment or disasslem-
bling any component containing fluids.
Dispose of all fluids according to local regulations and mandates.

NOTICE：

Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.

1. Turn the battery disconnect switch to the OFF position.
2. Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant -Change"for the correct procedure.

 Perkins Engine ECM ECU Flash Files Collection Download

  3. Disconnect harness assembly (1) from solenoid valve (2).
4. Loosen clamp hoses (6). Disconnect hose assembly (5) from solenoid valve (2).
5. Loosen clamp hoses (3). Disconnect hose assembly (4) from solenoid valve (2).
6. Remove bolts (7) and remove solenoid valve (2) from bracket (9).
Note: Note the orientation of the solenoid valve.
7. If necessary, follow Step 2. bthrough Step 7.b in order to remove bracket (9).
a. Remove bolts (8) from bracket (9).
b. Remove bracket (9) from the Diesel Emission Fluid (DEF) tank assembly.

 

Installation Procedure
Care must be taken to ensure that fluids are con- tained during performance of inspection, mainte- nance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable contain- ers before opening any compartment or disassem- bling any component containing fluids.

Dispose of all fluids according to local regulations and mandates.

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

1. Ensure that all components are clean and free

from wear and damage. If necessary, replace any components that are worn or damaged.

Typical example

2. If necessary, follow Step 2.a through Step 2.b in order to install bracket (9).

a. Position bracket (9) onto the DEF tank assembly.

b. Install bolts to bracket (9). Tighten the bolts to a torque of 9 N·m (80 lb in).

3. Position solenoid valve (2) to bracket (9). Ensure that the valve is correctly orientated.

4. Install bolts (4) to solenoid valve (2). Tighten the bolts to a torque of 9 N·m (80 lb in).

5. Connect hose assembly (5) to solenoid valve (2). Securely clamp hoses (6).

6. Connect hose assembly (4) to solenoid valve (2). Securely clamp hoses (3).

7. Connect harness assembly (1) to solenoid valve

8. Fill the cooling system with coolant. Refer to

Operation and Maintenance Manual, “Cooling

System Coolant - Change” for the correct

procedure.

9. Turn the battery disconnect switch to the ON
Perkins EST Diagnostic Adapter-High Quality
position.

Perkins 2806F-E18TA Industrial Engine Diesel Engine DEF Injector Installation Guide

This article mainly introduces the installation of DEF injector for Perkins 2806F-E18TA industrial engine diesel engine

Perkins Engine ECM ECU Flash Files Collection Download

 



1. Ensure that all components are clean, and free

from wear and damage. If necessary, replace any components that are worn or damaged.










2. Clean the gasket surface in Position (W) on the CEM. Ensure that no debris enters the CEM.

3. Clean the gasket surfaces in Position (Y) on DEF injector (1). Ensure that no debris enters the orifice plate in Position (X).

4. Position a new seal (7) onto DEF injector (1).

Ensure that the metal section of the gasket, faces the gasket surface in Position (W) on the CEM.

2023A& 2022A Perkins EST Electronic Service Tool Diagnostic Software Full Provide Installation Service




Typical example

5. Install a new gasket (6) to the CEM. Ensure that the gasket is correctly orientated.

6. Remove the plug from the CEM. Position DEF injector (1) to the CEM.

Note: To maintain cleanliness, the protective caps must remain in place until the final fluid connections are made.

7. Install washers (5) to bolts (4).

8.Apply Tooling (B) to the threads of bolts (4).

9. Install bolts (4) to DEF injector (1) hand tight.

10. Tighten bolts (4) to a torque of 5 N·m (44 lb in). 11. Turn bolts (4) through an extra 90 degrees.





12. Remove caps from hose assemblies (3) and DEF injector (1).

13. Connect hose assemblies (3) to DEF injector (1). Ensure that the hose assemblies are installed onto the hose assemblies original positions.

14. Remove the cap from harness assembly (2). Remove the plug from DEF injector (1).

15. Connect harness assembly (3) to DEF injector

assembly (2). Ensure that the harness assembly is not strained.

16. Install the Diesel Emission Fluid (DEF) line to the Diesel Emission Fluid (DEF) injector. Refer to

Disassembly and Assembly, “Diesel Exhaust Fluid Lines - Remove and Install” for the correct

procedure.

17. Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual, “Cooling System Coolant - Check” and refer to Operation

and Maintenance Manual, “Cooling System

Coolant - Change” for the correct filling procedure.

18. Turn the battery disconnect switch to the ON

position.
Perkins EST Diagnostic Adapter-High Quality

Perkins 2806F-E18TA industrial engine diesel DEF injector disassembly guide

This article introduces the Perkins 2806F-E18TA industrial engine diesel DEF injector disassembly instructions
2023A& 2022A Perkins EST Electronic Service Tool Diagnostic Software Full Provide Installation Service
Removal Procedure



NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

NOTICE
Care must be taken to ensure that fluids are con- tained during performance of inspection, mainte- nance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable contain- ers before opening any compartment or disassem- bling any component containing fluids.
Dispose of all fluids according to local regulations and mandates.

1. Turn the battery disconnect switch to the OFF position.

2. Drain the coolant from the cooling system into a

suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, “Cooling System Coolant - Change” for the correct draining procedure.

Perkins Engine ECM ECU Flash Files Collection Download

3. Remove the Diesel Emission Fluid (DEF) line from the Diesel Emission Fluid (DEF) injector. Refer to Disassembly and Assembly, “Diesel Exhaust Fluid Lines - Remove and Install” for the correct

procedure.

Typical example
4. Disconnect harness assembly (2) from DEF
injector (1). Cap the harness assembly.
5. Use Tooling (B) to plug connection on DEF injector ( 1).
6. Disconnect hose assemblies (3) from DEF injector ( 1). Use Tooling (A) to cap hose assemblies (3)
and DEF injector (1).

Perkins EST Diagnostic Adapter-High Quality

Typical example

7. Remove bolts (4) and washers (5) from DEF injector (1).

8. Remove DEF injector (1) and gasket (6) from the Clean Emission Module (CEM). Use a suitable

plug to plug the CEM.

9. Remove seal (7) from DEF injector (1).