This article introduces the installation of diesel exhaust pump for 2806F-E18TA industrial engine
Perkins EST Diagnostic Adapter-High Quality
NOTICE
Care must be taken to ensure that fluids are con- tained during performance of inspection, mainte- nance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable contain- ers before opening any compartment or disassem- bling any component containing fluids.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that all components are clean and free
from wear and damage. If necessary, replace any components that are worn or damaged.
2. If necessary, install a new filter (28) (not shown). Refer to Operation and Maintenance Manual,
“ Diesel Emission Fluid (DEF) Filter - Clean/ Replace” for the correct procedure.
3. Position diesel exhaust fluid pump (26) onto bracket (27).
4. Install bolts (25) to diesel exhaust fluid pump (26). Support the weight of the diesel exhaust fluid
pump as the bolts are installed.
5. Tighten bolts (25) to a torque of 19 N·m ( 168 lb in)
6. Remove cap from connection on the diesel
exhaust fluid pump.
7. Install manifold (23) to the diesel exhaust fluid
pump.
8. Install bolts (24) to manifold (23) finger tight.
9.Apply Tooling (B) to a new O-ring seal (21) (not shown) and a new O-ring seal (22) (not shown).
10. Position cap (20) onto manifold (23). Ensure that the cap is correctly installed onto the connection on the diesel exhaust fluid pump.
11. Install Allen head bolts ( 19) to cap (20) finger tight.
12. Tighten Allen head bolts (19) to a torque of
10 N·m (89 lb in).
13. Tighten bolts (24) to a torque of 4 N·m (35 lb in).
14. Position bracket ( 16) onto the bracket for diesel exhaust fluid pump.
15. Install bolts ( 12), bolts (15), and bolts (17) to
bracket (16). Tighten the bolts to a torque of 4 N·m (35 lb in).
16. Connected harness assembly (17) to the diesel exhaust fluid pump.
17. Position bracket ( 13) onto bracket (16). Install bolt (14) Tighten the bolt to a torque of 4 N·m (35 lb in).
18. Remove the plugs and caps from the connections and the diesel exhaust fluid line. Install diesel
exhaust fluid line (1). Refer toDisassembly and Assembly, “Diesel Exhaust Fluid Lines - Remove and Install” for the correct procedure.
19. Remove the plugs and caps from the connections and the diesel exhaust fluid line. Install diesel
exhaust fluid line (6). Refer toDisassembly and Assembly, “Diesel Exhaust Fluid Lines - Remove and Install” for the correct procedure.
20. Remove the plugs and caps from the connection and the diesel exhaust fluid line. Install the diesel exhaust fluid line to connection (11). Refer to
Disassembly and Assembly, “Diesel Exhaust Fluid Lines - Remove and Install” for the correct
procedure.
21. Connect hose assembly (3) to manifold DEF
heater and connection (4) (not shown) and the
diesel exhaust fluid pump. Tighten hose clamp (2) securely.
22. Connect hose assembly (8) to manifold DEF
heater and the diesel exhaust fluid pump. Tighten hose clamp (7) and hose clamp (9) securely.
23. Connect the hose assembly to connection (5). Tighten the hose clamp securely. Refer to the OEM for the correct procedure.
Perkins SPI2 Version 2018A Service & Parts Catalogue Software
24. Install solenoid valve ( 10). Refer toDisassembly and Assembly, “Solenoid Valve (DEF Heater
Coolant) - Remove and Install” for the correct procedure.
25. Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual, “Cooling System Coolant - Check” and Operation and
Maintenance Manual, “Cooling System Coolant - Change” for the correct filling procedure.
26. Turn the battery disconnect switch to the ON position.
没有评论:
发表评论