Translate

2023年3月30日星期四

How to Disassemble a Doosan Hydraulic Regulator

 Doosan DL220.PDF P181 Hydraulic Regulator Removal (HSG-94)

Doosan Diagnostic Tool uVIM Support Doosan Excavators High Quality 

IMPORTANT:
Different versions in relation to position of cable harness are possible.
In this connection, pay attention to Specifications of Vehicle
 Manufacturer.

 



1.
Figure 64, shows complete control unit.

2020 Doosan Daewoo Excavator Operation and Repair Manual PDF
2.
Mark installation position of different covers, housing and cable harness with valve housing.



3.
Remove socket head screws.



4.
Separate duct plate, 1st gasket, intermediate plate and 2nd gasket from valve housing.
(S) Box spanner (Torx TX-27) -5873 042 0025.
Remove retaining clip.

5.
Remove retaining clip.


6.
Remove socket head screws.
7.
Separate cover from housing and cable harness.
(S) Box spanner (Torx TX-27) -5873 042 002


8.
Disassemble opposite cover.
9.
Disconnect pressure regulator and remove cable harness.



10. Remove socket head screws, remove fixing plate and pressure regulators (3x).
(S) Box spanner (Torx TX-27) -5873 042 002


Doosan DMS-5 (Doosan Data Monitoring System) Diagnostic Software V1.6.3



11. Remove two socket head screws and locate housing provisionally, using adjusting screws. (Housing is under spring preload). Remove remaining socket and screws.
(S) Box spanner (Torx TX-27) -5873 042 002
(S) Adjusting screws -5870 204 036




12. Separate housing from valve housing by loosening adjusting screws uniformly.
(S) Adjusting screws -5870 204 036




13. Remove components (Figure 73).
14. Remove opposite pressure regulators, housing and components accordingly (Figure 74).



Doosan Diagnostic Tool DDT G2 SCAN( ECU ,DCU)Software 2016



2023年3月28日星期二

How To Do A JCB Backhoe Loader Power Side Shift Chain Adjustment

      How To Do A JCB Backhoe Loader Power Side Shift Chain Adjustment

JCB Backhoe Loader Power Sideshift - Chain Adjustment
The chain tension should be checked at the initial 100 hours
service and every 500 hours.
Check and Adjust

JCB ServiceMaster4 v23.2.1 (02.2023) Diagnostic Software Download and Installation


1 Park the machine on firm level ground, engage the
parking brake and set the transmission to neutral.
Lower the loader arms to the ground.


2 Position the carriage centrally and rest the bucket on
the ground, remove the starter key.


3 Check the chain tension which should be 5 to 10mm
(0.19 to 0.39in) deflection A at the mid point. The
tension should be equal for all chains.


4 If adjustment is required, slacken locknuts C and adjust
on nuts B as required, tighten locknuts C on
completion.


5 Repeat steps 3 and 4 for the opposite pair of chains.
Note: When there is no thread left for adjustment fit new
chains.


6 Operate the carriage side to side several times and
recheck the deflection.


2017 JCB Service Parts Pro+Service Repair Download

 
Removal
1 Park the machine on firm level ground, engage the
parking brake and set the transmission to neutral.
Lower the loader arms to the ground.


2 Position the carriage centrally and rest the bucket on
the ground, remove the starter key.


3 Undo and remove nuts B.


4 Remove split pins D and pin E.


5 Withdraw chains from the machine.
Assembly
1 Thread the chains around the pulley and secure to the
carriage with pin E, fit new split pins D.

02.2023 JCB All ECU’s Modules Flash File Download
2 Connect chain adjusters, tension chains as required,
see Check and Adjust



2023年3月27日星期一

Perkins Indup Strial Diesel Engine Exhaust Fluid Module Disassemble Guide

Perkins  2806F-E18TA Indup Strial Diesel  Engine Exhaust Fluid Module Disassemble  Guide

Perkins SPI2 Version 2018A Service & Parts Catalogue Software

Diesel Exhaust Fluid Module -
Assemble
Installation Procedure
NOTICE
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product.
Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.
Dispose of all fluids according to local regulations
and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened
component life
1. Ensure that all components are clean and free
from wear and damage. If necessary, replace any
components that are worn or damaged


2. If necessary, install filler cap (14) onto tank (16).
On some application the filler cap may be of a
different type. Refer to Original Equipment
Manufacturer (OEM) for the correct removal
procedure.
3. Position bracket (11) onto tank (16).
4. Install bolts (15) onto bracket (11). Tighten the
bolts to a torque of 4 N·m (35 lb in).

Perkins EST Electronic Service Tool Diagnostic Software Full Function 2022a
5. Position bracket (12) onto bracket (11).
6. Install bolts (13) to bracket (12). Tighten the bolts to a torque of 4 N-m (35 Ib in).

7. Install diesel exhaust fluid pump (10). Refer to Disassembly and Assembly, "Diesel Exhaust Fluid Pump -Remove and Install"for the correct procedure.
8. Position harness assembly (9) onto the bracket.
9. Install new cable straps (7) and new cable straps
(8) from harness assembly (9). Ensure that all the cable straps are installed in the original position.
Note: Ensure that the cable straps meet the OEM specifications.



10. Position relay (3) onto the bracket. Install bolt (1)
to the relay. Tighten the bolt to a torque of 4 N-m
(35 lb in).
11. Position relay (4) onto the bracket. Install bolt (2)
to the relay. Tighten the bolt to a torque of 4 N-m
(35 lb in).
12. Connect harness assembly (6) to relay (4).13. Connect harness assembly (5) to relay (3).
14. Turn the battery disconnect switch to the ON position.
End By: a. Install the voltage load protection module.
Refer to Disassembly and Assembly, "Voltage Load Protection Module -Remove and Install"
for the correct procedure.
b. Install the electronic control (Diesel Exhaust Fluid). Refer to Disassembly and Assembly,
"Electronic Control (Diesel Exhaust Fluid) -
Remove and Install"for the correct procedure.c. Install the manifold (DEF heater). Refer to Disassembly and Assembly, "Manifold (DEF Heater)-Remove and Install"for the correct procedure.
d. Install the solenoid valve (DEF heater coolant).
Refer to Disassembly and Assembly,
"Solenoid Valve (DEF Heater Coolant)-
Remove and Install"for the correct procedure.
e. Install the diesel exhaust fluid lines. Refer to Disassembly and Assembly, "Diesel Exhaust Fluid Lines-Remove and Install"for the correct procedure.
Perkins Engine ECM ECU Flash Files Collection Download

2023年3月23日星期四

Introduce how to disassemble and inspect Yanmar marine engine fuel injection pump

 Introduce how to disassemble and inspect Yanmar marine engine fuel injection pump


1,The fuel feed pump pumps fuel from the fuel tank, passes it through the fuel filter element, and supplies it to the fuel injection pump.
The fuel feed pump is mounted on the side of this engine and is driven by the (eccentric) cam of the fuel pump cam-
shaft. It is provided with a manual priming lever so that fuel can be supplied when the engine is stopped.
For Yanmar Diesel Engine Agriculture Excavator Tractor Marine Generator Diagnostic tool

2,5-1 Construction of fuel feed pump


1. Bottom body                            8. Lever assembly
2. Piston spring                            9.O-ring
3. Piston                                      10. Stop pin
4. Diaphragm spring                   11. Top body assembly
5. Diaphragm assembly              12. Packing
6. Pin                                           13. Cover
7. Lever return spring                 14. Small screw                                  
                                                   15. Cap
                                               

       Yanmar Engine Diagnostic Service Tool Software                         
                                                  
                                            
                                            

3 Disassembly and reassembly of fuel feed pump
3. 1 Disassembly
(1) Remove the fuel feed pump mounting nut, and take the fuel feed pump off the fuel injection pump.
(2) Clean the fuel feed pump assembly with fuel oil.
(3) After checking the orientation of the arrow on the cover, make match marks on the upper body and cover, remove the small screw, and disassemble the cover, upper body and lower body.
4. Reassembly
(1) Clean all parts with fuel oil, inspect, and replace any defective parts.
(2) Replace any packings on parts that have been disassembled.
(3) Make sure that the intake valve and discharge vaive on upper body are mounted in the proper direction, and that you don't forget the valve packing.
(4) Assemble the diaphragm into the body, making sure the diaphragm mounting holes are lined up (do not force).
(5) Align the match marks on the upper body of the pump and cover, and tighten the small screws evenly.

5, Fuel feed pump inspection
(1) Place the fuel feed pump in kerosene, cover the dis charge port with your finger, move the priming lever and check for air bubbles (Repair or replace any part which emits air bubbles).


(2) Attach a vinyl hose to the fuel feed pump intake, keep the pump at the specified depth from the fuel oil surface, move the priming lever by hand and check for sudden spurts of fuel oil from the discharge port. If oif is not spurted out, inspect the diaphragm and diaphragm spring and repair/replace as necessary.
(3) Diaphragm inspection Parts of the diaphragm that are repeatedly burned wifl become thinner or deteriorate over a long period of time.
Check the diaphragm and replace if necessary.

(4) Valve contact/mounting Clean the valve seat and vaive with air to remove any foreign matter.

Yanmar Heavy Equipment EPC 11.2009

(5) Inspect the diaphragm spring and piston spring for sett!-
ing and the piston for wear, and replace as necessary.
NOTE: Replace parts as an assembly.


2023年3月14日星期二

How to replace teeth on Liebherr Lidos bucket tooth

                          How to replace teeth on Liebherr Lidos bucket tooth

As a machine owner or operator, you should replace worn teeth at the first sign of any of the above conditions. To help your equipment perform to its full potential, we have compiled the key steps to properly replace your loader or excavator teeth. We hope it will help you.

 Liebherr Lidos EPC Mining Parts and Service Documentation Offline [11.2021]

1. Identify tooth type The three common types of teeth are: 

 a, Chisel teeth, used to excavate soil, sand and gravel in sandy terrain. 

 b, Rock teeth, used for digging iron ore, rock and hard ground, with high wear resistance. 

 c, Huya, provides acceptable penetration for excavating compacted soils and clays. 

 2. Determine the size and direction of the tooth shape of the rolling pin New teeth must be the same size as previous teeth to ensure smooth installation and efficient machine operation. Also, note the orientation of the rolling pin. The prongs are available as top prongs and side prongs - the top prongs must be mounted vertically, while the side prongs must be mounted horizontally. 

 3. Extract old teeth and install new ones Start by adjusting the loader or excavator bucket into a convenient position for maneuvering. Use a pin removal tool to pull out the rolling pin and remove the old, worn teeth. Each shank is cleaned to prepare it for new teeth. The teeth fit and attach to the calf. Slide each new tooth and line them up with the holes through the shank. Insert the rolling pin and hammer, or hold it through the hole, making sure the pin is fully inserted. Not all teeth have the same type of tooth retainer that holds them in place. Some have vertical pins, some have horizontal pins, and some don't even use pins at all. For this reason, it's a good idea to consult your owner's manual and learn about your manufacturer's recommended removal methods before starting work.

Liebherr Lidos EPC Parts and Service Documentation Offline [12.2021]

Note: When installing replacement teeth, make sure to wear safety gloves to ensure safety.

 

you are done! Using these simple steps, you can easily replace a loader or excavator tooth without professional help. Replacing teeth will allow excavators and loaders to dig deeper and dig more efficiently, even in challenging conditions.

 

2023年3月13日星期一

How to Disassemble Doosan Hydraulic Controller

Disassembly of Doosan DL220 hydraulic controller

Doosan Diagnostic Tool uVIM Support Doosan Excavators High Quality
IMPORTANT:
     Different versions in relation to position of cable harness are possible.
In this connection, pay attention to Specifications of Vehicle
 Manufacturer.

 

 

 

 
1.
Figure 64, shows complete control unit.




2.
Mark installation position of different covers, housing and cable harness with valve housing.




3.
Remove socket head screws.

Doosan Diagnostic Tool DDT G2 SCAN( ECU ,DCU)Software 2016
4.
Separate duct plate, 1st gasket, intermediate plate and 2nd gasket from valve housing.
(S) Box spanner (Torx TX-27) -5873 042 0025.
Remove retaining clip.



5.
Remove retaining clip.


6.
Remove socket head screws.
7.
Separate cover from housing and cable harness.
(S) Box spanner (Torx TX-27) -5873 042 002



8.
Disassemble opposite cover.
9.
Disconnect pressure regulator and remove cable harness.



10. Remove socket head screws, remove fixing plate and pressure regulators (3x).
(S) Box spanner (Torx TX-27) -5873 042 002






11. Remove two socket head screws and locate housing provisionally, using adjusting screws. (Housing is under spring preload). Remove remaining socket and screws.
(S) Box spanner (Torx TX-27) -5873 042 002
(S) Adjusting screws -5870 204 036



12. Separate housing from valve housing by loosening adjusting screws uniformly.
(S) Adjusting screws -5870 204 036



Doosan DMS-5 (Doosan Data Monitoring System) Diagnostic Software V1.6.3
13. Remove components (Figure 73).
14. Remove opposite pressure regulators, housing and components accordingly (Figure 74).









2023年3月10日星期五

How to Installation the Injection Pump of The New Holland Engine

  Installation of Injection Pump of New Holland_b115 Engine
STEP 1

2023 CASE New Holland Electronic Service Tools (CNH EST v9.7Up3) Engineering Diagnostic Software


Replace gasket on pump mounting flange.


STEP 2


Install pump and tighten the three mounting nuts.




STEP3


Install lock washer and nut, torque nut to 66 to 70
lb-ft (90 to 95 Nm).
WARNING: Use caution when installing nut and
washer they can be dropped inside of the engine.




STEP4


Apply Loctite 5205 to the surface of the cover plate,
install cover plate and mounting bolts, tighten bolts.




STEP 5

Connect wire to temperature sensor.




STEP 6

Connect the fuel feed line to the injector pump.
SECTION 10 - ENGINE - CHAPTER 1 7
Issued 12-04



STEP 7


Remove covers from lines and fittings. Connect fuel
injector lines (1), connect fuel return line (2), and
boost line (3) to the pump. 



STEP 8

CNH DPA5 Adapter New Holland Heavy Duty mechanical Diagnostic Tool


Install oil filler tube (3), mechanical fuel pump (2),
and fuel filter (1) on the engine.



STEP 9



Install the injector line retaining bracket mounting
bolts.




STEP 10

Loosen injector pump locking bolt and install the
slotted plate, tighten the locking bolt to 9 to 10 lb-ft
(12 to 14 Nm).



STEP 11



Make sure locking pin is disengaged from gear.




STEP 12
Remove the engine turning tool and install the
starter.




STEP 13


If the machine has only one battery, connect the
negative battery cable to the battery. Install the
battery cover.




STEP 14



Install grounding cable (2) onto the terminal. Install
the jumper cable (3) on the terminal and start the
terminal nut (1) onto the terminal. Tighten the
terminal nut.




STEP 15



Install the front rocker arm cover and injector line
retaining bracket mounting bolt.




STEP 16



Install the throttle cable into the bracket and tighten
the jam nut.




STEP 17



Install and thighten the two throttle arm mounting
bolts.



STEP 18


New Holland AG& CE Service Manuals PDF 2019Download (170GB)

Connect the power lead to the injector pump.




STEP 19
Actuate the lever on the mechanical fuel pump to
prime the fuel system.


STEP 20
Start the machine and check for fuel leaks, check
and adjust throttle linkage as needed

How to relieve hydraulic pressure in the hydraulic circuit of a CAT excavator.

  How to relieve hydraulic pressure in the hydraulic circuit of 312D2 and 313D2 excavators   Steps to relieve pressure:   Caterpillar ET 202...